PhD Student in Materials Science and Engineering UFSCar/Brazil
15
Scopus Publications
263
Scholar Citations
8
Scholar h-index
8
Scholar i10-index
Scopus Publications
Mechanically Deposited Wear-Resistant Amorphous Zr55Cu30Al10Ni5 Coatings Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, et al. Advanced Engineering Materials, 2026 Zr 55 Cu 30 Al 10 Ni 5 amorphous coatings were deposited onto AISI 1010 carbon steel substrates via high‐energy ball milling of as‐spun metallic glass ribbons. Their tribological performance under dry sliding was evaluated using a reciprocating pin‐on‐plate setup and compared with both the crystalline alloy and the bare carbon steel. The crystalline Zr 55 Cu 30 Al 10 Ni 5 (430 HV 0.3 ) alloy exhibited the lowest coefficient of friction (COF ≈ 0.28), whereas the amorphous coating achieved superior hardness (550 HV 0.3 ), three times higher than the substrate (162 HV 0.3 ), with a COF of ≈0.39. The amorphous coating showed a specific wear rate (≈10 −4 mm 3 N −1 m −1 ), an order of magnitude lower than the carbon steel (≈10 −3 mm 3 N −1 m −1 ). Wear mechanisms differed: the amorphous coating underwent mainly adhesive and delamination wear with minor abrasive and oxidative contributions, while the crystalline alloy experienced mixed abrasive‐adhesive wear with mild oxidation. These results highlight the promise of mechanically deposited Zr‐based amorphous coatings as effective wear‐resistant surfaces for steel substrates.
Mechanically Deposited Wear‐Resistant Amorphous Zr 55 Cu 30 Al 10 Ni 5 Coatings T Ferreira, PC Bortolini, AL Vidilli, PW Barbosa Marques, JA Moreto, ... Advanced Engineering Materials 28 (3), e202502339 , 2026 2026
Plasma transferred arc deposition of Fe-Cr-Mo-Nb-B coatings: Influence of processing parameters on wear resistance LCM Rodrigues, GY Koga, T Ferreira, C Bolfarini, CS Kiminami, GS Prass, ... Surface and Coatings Technology, 133085 , 2025 2025
Air carbon arc gouging and submerged-arc welding: Insights into sensitization and mechanical behavior of AISI 2205 duplex stainless steel A de Bribean Guerra, T Ferreira, C Bolfarini, GY Koga Journal of Materials Research and Technology 36, 6196-6218 , 2025 2025 Citations: 4
Enhanced wear resistance of a novel Al-based quasicrystalline phase-forming alloy obtained by laser powder bed fusion D de Campos Fernandes, APM de Araujo, T Ferreira, V Uhlenwinkel, ... Materials Letters 382, 137936 , 2025 2025 Citations: 2
Effect of building direction and heat treatment on the wear behavior of H13 tool steel processed by laser powder bed fusion AP Oliveira, T Ferreira, RT Coelho, C Bolfarini, P Gargarella Journal of Materials Research and Technology 33, 9802-9810 , 2024 2024 Citations: 8
Assessment of HVAF thermally sprayed coatings: Unraveling microstructural, electrochemical, and tribological performance using glass former Fe-Cr-Mo-Nb-B feedstock powder IGC Mota, GY Koga, LCM Rodrigues, ARC Nascimento, FB Ettouil, ... Journal of Alloys and Metallurgical Systems 6, 100081 , 2024 2024 Citations: 2
Journal of Alloys and Metallurgical Systems IGC Mota, GY Koga, LCM Rodrigues, ARC Nascimento, FB Ettouil, ... Journal of Alloys and Metallurgical Systems 6, 100081 , 2024 2024
Enhanced wear resistance of a novel Al-based quasicrystalline phase-forming alloy obtained by laser powder bed fusion DC Fernandes, APM de Araujo, T Ferreira, V Uhlenwinkel, P Gargarella Materials Letters 382, 5 , 2024 2024 Citations: 2
Tuning the hydride stability of the TiVNb-based alloys by equimolar Cr/Al addition T Ferreira, N Pineda-Romero, WJ Botta, G Zepon, C Zlotea Intermetallics 161, 107992 , 2023 2023 Citations: 12
New Al-alloys with dispersed stable quasicrystal approximant phases: Overcoming the barrier of conventional casting processing and microstructure design T Ferreira, GY Koga, P Gargarella, CS Kiminami, WJ Botta, C Bolfarini Journal of Manufacturing Processes 98, 196-205 , 2023 2023 Citations: 4
Air carbon arc gouging of austenitic stainless steels prior to arc welding–opportunities and risks GY Koga, T Ferreira, AP de Bribean Guerra, D Cunha, JGG Wiezel, ... Journal of Materials Processing Technology 303, 117524 , 2022 2022 Citations: 14
Manufacture and Characterization of Polypropylene (PP) and High-Density Polyethylene (HDPE) Blocks for Potential Use as Masonry Component in Civil Construction. Polymers 2022 … T Ferreira, G Mendes, A Oliveira, C Dias s Note: MDPI stays neutral with regard to jurisdictional claims in published … , 2022 2022 Citations: 3
Strong and ductile recycled Al-7Si-3Cu-1Fe alloy: controlling the morphology of quasicrystal approximant α-phase by Mn and V addition T Ferreira, AL Vidilli, G Zepon, CS Kiminami, WJ Botta, C Bolfarini Journal of Alloys and Compounds 888, 161508 , 2021 2021 Citations: 22
Challenges in optimizing the resistance to corrosion and wear of amorphous Fe-Cr-Nb-B alloy containing crystalline phases GY Koga, T Ferreira, Y Guo, DD Coimbrão, AM Jorge Jr, CS Kiminami, ... Journal of Non-Crystalline Solids 555, 120537 , 2021 2021 Citations: 62
Desenvolvimento de ligas de alumínio recicladas contendo a fase primária Al (Fe, TM) Si aproximante de quasicristal: controle da microestrutura visando aplicações tribológicas … T Ferreira 2021
Functionally graded aluminum reinforced with quasicrystal approximant phases–improving the wear resistance at high temperatures T Ferreira, GY Koga, IL de Oliveira, CS Kiminami, WJ Botta, C Bolfarini Wear 462, 203507 , 2020 2020 Citations: 27
Rotational outward solidification casting: An innovative single step process to produce a functionally graded aluminum reinforced with quasicrystal approximant phases T Ferreira, IL de Oliveira, G Zepon, C Bolfarini Materials & Design 189, 108544 , 2020 2020 Citations: 16
Thermo-optical properties of perfluorinated sulfonic acid membranes: an investigation of hydration based on absorption spectra DT Dias, G Lopes, T Ferreira, IL Oliveira, CD Rosa Applied Spectroscopy 71 (11), 2504-2511 , 2017 2017 Citations: 5
Prediction of the surface finishing roughness effect on the fatigue resistance of Ti-6Al-4V ELI for implants applications PSCP da Silva, LC Campanelli, CAE Claros, T Ferreira, DP Oliveira, ... International Journal of Fatigue 103, 258-263 , 2017 2017 Citations: 39
Desenvolvimento de camadas ricas no intermetálico α-Alx (Fe, Mn, Cr) ySiz em ligas Al-Si por solidificação controlada T Ferreira Universidade Tecnológica Federal do Paraná , 2016 2016 Citations: 1
MOST CITED SCHOLAR PUBLICATIONS
Challenges in optimizing the resistance to corrosion and wear of amorphous Fe-Cr-Nb-B alloy containing crystalline phases GY Koga, T Ferreira, Y Guo, DD Coimbrão, AM Jorge Jr, CS Kiminami, ... Journal of Non-Crystalline Solids 555, 120537 , 2021 2021 Citations: 62
Prediction of the surface finishing roughness effect on the fatigue resistance of Ti-6Al-4V ELI for implants applications PSCP da Silva, LC Campanelli, CAE Claros, T Ferreira, DP Oliveira, ... International Journal of Fatigue 103, 258-263 , 2017 2017 Citations: 39
Alimentação e cultura E RECINE, P Radaelli, T Ferreira Departamento de Nutrição, Universidade de Brasília. Secretaria de Políticas … , 2008 2008 Citations: 36
Functionally graded aluminum reinforced with quasicrystal approximant phases–improving the wear resistance at high temperatures T Ferreira, GY Koga, IL de Oliveira, CS Kiminami, WJ Botta, C Bolfarini Wear 462, 203507 , 2020 2020 Citations: 27
Strong and ductile recycled Al-7Si-3Cu-1Fe alloy: controlling the morphology of quasicrystal approximant α-phase by Mn and V addition T Ferreira, AL Vidilli, G Zepon, CS Kiminami, WJ Botta, C Bolfarini Journal of Alloys and Compounds 888, 161508 , 2021 2021 Citations: 22
Rotational outward solidification casting: An innovative single step process to produce a functionally graded aluminum reinforced with quasicrystal approximant phases T Ferreira, IL de Oliveira, G Zepon, C Bolfarini Materials & Design 189, 108544 , 2020 2020 Citations: 16
Air carbon arc gouging of austenitic stainless steels prior to arc welding–opportunities and risks GY Koga, T Ferreira, AP de Bribean Guerra, D Cunha, JGG Wiezel, ... Journal of Materials Processing Technology 303, 117524 , 2022 2022 Citations: 14
Tuning the hydride stability of the TiVNb-based alloys by equimolar Cr/Al addition T Ferreira, N Pineda-Romero, WJ Botta, G Zepon, C Zlotea Intermetallics 161, 107992 , 2023 2023 Citations: 12
Effect of building direction and heat treatment on the wear behavior of H13 tool steel processed by laser powder bed fusion AP Oliveira, T Ferreira, RT Coelho, C Bolfarini, P Gargarella Journal of Materials Research and Technology 33, 9802-9810 , 2024 2024 Citations: 8
Thermo-optical properties of perfluorinated sulfonic acid membranes: an investigation of hydration based on absorption spectra DT Dias, G Lopes, T Ferreira, IL Oliveira, CD Rosa Applied Spectroscopy 71 (11), 2504-2511 , 2017 2017 Citations: 5
Air carbon arc gouging and submerged-arc welding: Insights into sensitization and mechanical behavior of AISI 2205 duplex stainless steel A de Bribean Guerra, T Ferreira, C Bolfarini, GY Koga Journal of Materials Research and Technology 36, 6196-6218 , 2025 2025 Citations: 4
New Al-alloys with dispersed stable quasicrystal approximant phases: Overcoming the barrier of conventional casting processing and microstructure design T Ferreira, GY Koga, P Gargarella, CS Kiminami, WJ Botta, C Bolfarini Journal of Manufacturing Processes 98, 196-205 , 2023 2023 Citations: 4
Manufacture and Characterization of Polypropylene (PP) and High-Density Polyethylene (HDPE) Blocks for Potential Use as Masonry Component in Civil Construction. Polymers 2022 … T Ferreira, G Mendes, A Oliveira, C Dias s Note: MDPI stays neutral with regard to jurisdictional claims in published … , 2022 2022 Citations: 3
Enhanced wear resistance of a novel Al-based quasicrystalline phase-forming alloy obtained by laser powder bed fusion D de Campos Fernandes, APM de Araujo, T Ferreira, V Uhlenwinkel, ... Materials Letters 382, 137936 , 2025 2025 Citations: 2
Assessment of HVAF thermally sprayed coatings: Unraveling microstructural, electrochemical, and tribological performance using glass former Fe-Cr-Mo-Nb-B feedstock powder IGC Mota, GY Koga, LCM Rodrigues, ARC Nascimento, FB Ettouil, ... Journal of Alloys and Metallurgical Systems 6, 100081 , 2024 2024 Citations: 2
Enhanced wear resistance of a novel Al-based quasicrystalline phase-forming alloy obtained by laser powder bed fusion DC Fernandes, APM de Araujo, T Ferreira, V Uhlenwinkel, P Gargarella Materials Letters 382, 5 , 2024 2024 Citations: 2
Método Simplificado para Relacionar Concentração de DBO, Vazão e os Conceitos de Permânecia e Risco FW Machado, FA Schmidt, TN Ferreira, CVS Fernandes, MFA PORTO XVII Simpósio Brasileiro de Recursos Hídricos , 2007 2007 Citations: 2
Measurement of the density of states of a Al6Ru quasicrystalline alloy by ultrafast thermomodulation TAE Ferreira, LH Acioli, FLA Machado Solid state communications 118 (1), 37-41 , 2001 2001 Citations: 2
Desenvolvimento de camadas ricas no intermetálico α-Alx (Fe, Mn, Cr) ySiz em ligas Al-Si por solidificação controlada T Ferreira Universidade Tecnológica Federal do Paraná , 2016 2016 Citations: 1
Mechanically Deposited Wear‐Resistant Amorphous Zr 55 Cu 30 Al 10 Ni 5 Coatings T Ferreira, PC Bortolini, AL Vidilli, PW Barbosa Marques, JA Moreto, ... Advanced Engineering Materials 28 (3), e202502339 , 2026 2026